SIL-B  Relays are for primary distribution which is ideal to protect a feeder by means of current and voltage functions and it is normally used with a circuit breaker as cutting element.

Aasy mounting, and fast settings make the SIL-B series the right solution for industrial and utility feeder protection. SIL-B provides complete feeder protection, with overcurrent, overvoltage, undervoltage, directional

Uses auxiliary power supply 110-230 Vac/90-300 Vdc or 24-48 Vdc.

Its reduced size makes the SIL-B series relays iasy to install and its light weight helps the customer to save costs in transport.

Contact us

    Name (required)

    Lastname (required)

    Email (required)

    Company (required)

    Select your Country*

    Your message (required)

    This site is protected by reCAPTCHA and the Google
    Privacy Policy and
    Terms of Service apply.

    [Download not found]

    Features

    The SIL-B is a relay for primary distribution which is able to protect a feeder by means of current and voltage functions. It is normally used with a circuit breaker as cutting element.

    • SIL-B is used with auxiliary power supply 110-230 Vac/90-300 Vdc or 24-48 Vdc.
    • Protection functions available in SIL-B are the following: 50, 50N/G, 67, 67N, 46, 59, 59N, 27, 32/40, 79, 50BF, 52, 49, 86, CLP, 49T, 74TCS, 25,  81 U/O, 37, IRG-B
    • 79 protection function (Recloser) allows up to 5 attempts of reclosing which can be programmed by the user.
    • SIL-B has metallic box with high electromagnetic compatibility level (EMC) and wide range of operating temperature.
    • Its reduced size makes the SIL-B relay easy to install and its light weight helps the customer to save costs in transport.
    • Direct signalling/control both of the circuit breaker (52 function), both of the recloser (79 function).
    • To allow the communication relays have a communication port on the front of the equipment.
    • Two rear ports on the back for remote communication. Two communication protocols can be used simultaneously:
      • MODBUS RTU
      • IEC 60870-5-103, IEC 61850, DNP 3.0 or IEC 60870-5-104.
    • SIL-B can show different measurements like:
      • Phase r.m.s. currents, neutral r.m.s. current, positive / negative sequence currents.
      • Phase r.m.s. voltages, residual neutral voltage r.m.s, voltage between phases and Busbar phase voltage.
      • Angle current of each phase respect to phase A voltage.
      • Cos Phi (power factor and each phase power factor).
      • Active power, reactive and apparent power (Total power and each phase power).
      • Line frequency and Busbar frequency.
      • Phase difference between phase B line voltage and busbar voltage.
    • The SIL-B has 8 configurable inputs and 7 configurable outputs.
    • 2 Oscillographic records, non-volatile RAM memory in order to store up to 1.000 events and 20 fault reports, without power supply thanks to its internal RTC (Real Time Clock).

    Ansi Code Functions

    50 Phase instantaneous overcurrent
    50N/G Neutral instantaneous overcurrent calculated/measured
    67 Inverse time directional phase overcurrent
    67N Inverse time directional neutral overcurrent
    46 Negative sequence inverse-time overcurrent
    59 Instantaneous phase overvoltage
    59N Instantaneous neutral overvoltage
    27 Instantaneous phase undervoltage
    32/40 Instantaneous directional overpower
    79 Relé de Reenganche C.A.
    50BF Circuit Breaker opening fault
    52 Circuit Breaker monitoring
    49 Thermal image
    86 Trip output lockout with PLC
    CLP Cold Load Pick-up
    49T External trip
    74TCS Trip circuit supervision
    25 Synchronism

    Documents

    Technical Sheets

    [Download not found]
    [Download not found]

    User’s Manuals

    [Download not found]
    [Download not found]

    Software

    Communication Software for SIA & SIL protection relays

    The SICom PC software has been designed and programmed to gain access to all of Fanox relays information, to modify the settings and configuration, check states and measurements and to analyse and save events and fault reports using a graphic-friendly user interface.

    SICom software works with the Windows® Windows 7, Windows 8, Windows 8.1 and Windows 10 operating system.

    • General data reading: Complete model, Version, Serial number, etc.
    • States reading
    • Measurements reading
    • Reading and changing settings
    • Reading and changing configuration
    • Reading and deleting events
    • Reading and deleting fault reports
    • Reading and deleting demand current (load data profiling)
    • Reading and saving oscillographic records in Comtrade format
    • Changing the user passwords
    • Saving and Loading settings files
    • Saving and Loading configuration files
    • Saving events and fault reports
    • Saving demand current (load data profiling)
    • Date-time synchronization
    • Configuring the communication parameters
    • Reading and changing counters
    • Commands for opening and closing the circuit breaker and block/unblock the recloser
    • Configuration of the inputs
    • Configuration of the outputs
    • Configuration of the causes that start a Fault Report

    The update of the software does not require any user´s action, this is, if the computer is connected to Internet, SICom updates itself when it is started.
    It will allow you to prepare all the settings and relay configurations without having the relay connected to the PC (offline mode), reducing engineering and commissioning time.
    SICom program uses Modbus protocol, so only the ports with this protocol can be used to establish the communication.

    Aplication Diagram

    Comparison Table

    SIL-ASIU-CSIL GSIL-C
    TypeOC & EF PROTECTIONVOLTAGE & FREQUENCY PROTECTIONLINE, FEEDER AND GENERATOR PROTECTIONLINE, FEEDER AND GENERATOR PROTECTION
    Auxiliary Supply24-230 Vdc/Vac24-230 Vdc/Vac24-48Vdc or 48-230 Vac/dc or 24-230 Vac/dc24-230 Vdc/Vac
    Consumption3,3 – 4,5 W< 6 W. 24-230 Vdc/Vac < 10VA24-48 Vdc and 48-230 Vac/dc < 10VA. 24-230Vac/dc < 20VA24-230Vac/dc < 20VA
    Current measurementStandard CT > 0,5VAn/aStandard CT > 0,5VAStandard CT > 0,5VA
    LPCTn/an/an/an/a
    Voltage measurementn/aVT or directly to the low voltage lineVT or directly to the low voltage lineVT or directly to the low voltage line
    VT connection typen/aAdjustableAdjustableAdjustable
    502n/a22
    50G2n/a11
    50N2n/a11
    50/512n/a4 levels of 67 *4 levels of 67 *
    50/51G2n/a2 levels of 67G *2 levels of 67G *
    50/51N2n/a2 levels of 67N *2 levels of 67N *
    67GI1n/a11
    67NI1n/a11
    50/51/67G 1n/a**
    50/51/67n/an/a**
    SOFT1n/a11
    64REF1n/a11
    521111
    BF1111
    491n/a11
    49T1111
    791111
    HLTn/a√√√
    461n/a11
    CLP1n/a11
    74TCS1111
    74CCSn/a1n/an/a
    Trip Block1n/a11
    68 (Trip Bus)1111
    86√√11
    46BC√n/a11
    60CTS 1n/a11
    60VTSn/an/a11
    Programmable LogicV3V3√√
    371n/a11
    59n/a222
    59N1322
    47n/a111
    27n/a422
    27V1n/a211
    32/40n/an/a44
    81U/On/a844
    25n/a111
    24n/a222
    59-Ln/a111
    27-Ln/a111
    81Rn/a644
    78n/a211
    IRIG-Bn/aOptionalOptionalOptional
    Counters√√√√
    Commands√√√√
    Sett. Group4444
    Inputs3 / 5 / 6 / 9118 / 16 / 24 / 8 + 4 AFD11
    Outputs3 / 4 / 5 / 6 / 757 / 11 / 18 / 7 + 4 HS-O5
    LEDs8 configurable11 configurable11 configurable11 configurable
    HMI20x2 LCD + 11 keys20x4 LCD + 13 key20x4 LCD + 13 keys20x4 LCD + 13 keys
    52 & 79 HMI2 LEDs + 4 keys2 LEDs + 4 keys2 LEDs + 4 keys3 LEDs + 4 keys
    Event2048307230723072
    Fault Reportconfigurable up to 100configurable up to 100configurable up to 100configurable up to 100
    OscillographyConfigurable up to 100 recordsconfigurable up to 100configurable up to 100configurable up to 100
    Current demand√n/a√√
    Local Port (frontal)Micro USBMicro USBMicro USBMicro USB
    Remote Port (rear)RS485 or EthernetRS485 or EthernetRS485 or Ethernet or Fiber OpticRS485 or Ethernet
    Communications ProtocolsRS485 (ModBus RTU or IEC60870-5-103 or DNP3.0 Serial) RJ45 (Modbus TCP/IP or DNP3 TCP/IP or IEC 60870-5-104) RJ45 (IEC61850) + SNTP protocolRS485(ModBus RTU or DNP3.0 Serial or IEC60870-5-103) RJ45 (Modbus TCP/IP or DNP3.0 TCP/IP or IEC60870-5-104) + SNTP protocolRS485(ModBus RTU or DNP3.0 Serial or IEC60870-5-103) RJ45(Modbus TCP/IP or DNP3.0 TCP/IP or IEC60870-5-104) RJ45(IEC 61850) FO-LC(IEC61850) + SNTP protocolRS485(ModBus RTU or DNP3.0 Serial or IEC60870-5-103) RJ45 (Modbus TCP/IP or DNP3.0 TCP/IP or IEC60870-5-104) + SNTP protocol
    Size of177 x 107 mm177 x 107 mm198 x 187 mm177 x 107 mm

    Related Products

    SIC-A
    Redundancy Protocols Gateway (PRP/HSR)

    Communication Solutions for Smart Grid.

    This technology implies an important technology leap for the industry, due to the transmission of a huge amount of data, in many cases in real time, is required.

    To implement these new technologies the industry requires an easy and flexible system that is able to adapt to its all requirements.
    The protocols gateways provide an easy way to adapt the existing devices to the new technologies.

    More info ->

    SIL-G
    Generator/Feeder Protection Relays

    Fanox SIL-G is a relay for primary distribution which can protect a feeder by means of current, voltage and frequency functions.

    His main features include Arc Flash Protection with 4 inputs and 4 high-speed outputs, and being able to choose between universal supply and Self-Powered through VTs.

    It also brings some innovative features such as WIFI connection providing you complete safety during maintenance.

    More info ->